We can supply 56 inches shuttle loom parts,1515 and GA615 woven fabric machine introduction Transmission mechanism:

1, transmission mode: single motor V-belt drive

2, control mode: single side switch control clutch and brake device.

3, clutch type: cone friction disc

4, brake type: steel brake

5, the wheel shaft and crank ratio 1:2 Main bodies and their specifications First,

sent by the agency

1, type: semi positive semi negative automatic warp, automatic adjustment of warp tension.

2, a beam axle diameter: 110mm

3, beam disc diameter: 495mm, 550mm Two,

through the parking device

1, type: front and rear swing mechanical menopause

2, the tooth movement cycle: crank shaft rotation 2 times

3, menopause column number:

4 column Three, opening mechanism

1, type: the inside of the disc mounted on the top of the crane

2, the disc diameter: 42mm

3, heald frame number: 2 page heald frame (can be adjusted to the plate of the twill or to modify the multi arm lifting device 16 page) (5)

Four, the shuttle mechanism

1, type: under the shuttle

2, the shuttle size: length 343mm, width 44.5mm, high 33.5mm (left hand)

3, the skin type: movable skin knot

4, leather knot size: long 105mm, wide 30mm, high 32mm

5, at the same time rotor diameter: 76mm Five,

beating up mechanism In

1, type: crank shaft hand beating

2, crank shaft diameter: 40mm, 1515K diameter of 42mm.

3, crank shaft radius: 76mm

4, crank shaft center distance: 1540mm (1350mm loom), 1714mm (1500mm loom), 1816mm (1600mm loom), 2019mm (1800mm loom)

5, hand type: bearing type hand

6, hand length: 289mm

7, hand bolt diameter: 25mm, From

8, hand center to the rockshaft Center: 685mm

9, the rocking shaft type: whole root

10, shaft diameter: 38mm

11, reed type: wood structure

12, shuttle board length: 1423mm (1350mm loom), 1597mm (1500mm loom), 1699mm (1600 looms), 1902mm (1800mm loom) 13, box bottom plate length: 581mm side 600mm side switch, the shuttle magazine. Six, warp protection device Type: reed Seven,

coiling mechanism

1, type: seven gear intermittent coiling

2, weft density range: 16-32 root /cm

3, the diameter of the piercing roller: 127mm

4, guide cloth roller diameter: 32mm

5, roller diameter: 95mm Eight,

the extension device

1, type: single row copper ring roller

2, only a few: around 1 groups

3, the weft shear hammer: the role of the role of the hammer Nine,

broken weft stop device

1, type: weft cam control side weft fork or point peck type weft

2, coiling and rewinding device Ten, weft feeding device 1, type: automatic shuttle type 2, the shuttle magazine: vertical in-line

3, shuttle storage capacity: 10

4, change the shuttle to induce a device: adopt the probe to change the shuttle to induce the device (to the request not high of the fabric also can use the weft fork to change the shuttle to induce the device)

5, shuttle safety device: when the shuttle mechanism failure, immediately stop, avoid the machine rolling loss

6, free shuttle, shuttle side parking device: Suokunei shuttle or shuttle position on the side, immediately stop automatically

7, prevent residual weft weaving device: can avoid the burr, double weft defects, improve the quality of fabric Eleven, the main equipment and specifications 1, weft tube: total length 180mm, head diameter 27mm 2, steel reed, total length 1394mm (1350mm loom), 1568mm (1500mm loom), 1669mm (1600mm loom), 1873mm (1800mm). Height: 120mm 3, heald length: plain or twill 305mm, dobby 330mm 4, menopause tablets: length 120mm, width 11mm, closed 5, triangle belt: A type 2286